7400 SAN FERNANDO RD. SUN VALLEY, CALIFORNIA 91352

ABOUT US	CONTACT US	ORDERING	FREE CATALOG

Copyright J.F.K. Co. Precision Products 2008 - 2009

201-A	Adapter Collet 2-1/2"
201-B	Adapter Collet 3"
201-K	Key
202-A	Ring, Nose L1
202-B	Ring, Nose L0
202-C	Ring, Nose L00
202-D	Ring, Nose Threaded
202-E	Ring, Nose L2
203	Tube, Draw
204	Hub Adapter
205

Actuator Assembly
	2701 Collar
	2702 Screw
	2703 Nut
	2704 Bearing
	2705 Cam
	2706 Collar (Knurled)
		2753 Finger
		2754 Pin, Pivot
		2707 Pin, Index
		2708 Knob
		2709 Screw
		2710 Spring

206	Handle Casting
207	Nut
208	Screw
209	Nut
210	Rod, Handle
211	Handle
212	Screw
213	Ring, Index
214	Screw
215	Bracket
216	Pin
217	Connector, Rod
218	Rod
219	82 degree Head Allen

To install HAND LEVER CLOSER

1. Mount hub (204) on back end of spindle. Hubs for plain spindles should be pressed on completely so that the end of the spindle will seat against the bottom of the bore in the hub. Lock with the two set screws (214). Threaded hubs should be screwed onto the spindle so that the end will abut the collar or locknut on the spindle. In some cases it may be necessary to remove the thrust collar or locknut on the spindle to allow complete adaption of the hub.
2. Mount the index ring (213) on the hub (204) by means of the three screws (212). It is very important that the periphery of the ring is concentric with the axis of the spindle. It is suggested that the mounting screws be loostened slightly and the ring positioned accurately with an indicator. After determining that is it running true the screws should be tightened securely.
3. Where applicable install nose ring (202) to spindle nose.
4. Check the taper in the front of the lathe spindle to ascertain the there are no nicks of bumps on the surface. By the use of an indicator determine that the spindle turns without runout in the taper.
5. Install the closer unit thru the back end of the spindle, slipping the actuator collar (2706) over the index ring (213). Pull out the index pin (2708) and turn so that the set screw (2709) is resting on the edge of the collar (2706).
6. Mount bracket (215) on case of lathe in such a position that the linkage will be at the same elevation as the spindle. Connect linkage to closer unit.
7. Insert collet adapter (201) in nose of spindle.
8. Insert desired collet into adapter and turn collar (2706) so that draw tube (203) will engage collet. Insert piece of material of the required size into the coller and with the unit in the released position turn the collar (2706) until the material is lightly held. Move the hand lever back and forth until the desired tension is obtained by turning the collar. Release the index pin (2708) allowing it to enter the closet hole in the index plate (213). The collar may require turning slightly to allow the index pin to seat completely. CAUTION: Avoid excessive tension on collet.
9. Adjust linkage so that the operating handle will travel angularly equal from open to middle position and closed to middle position.

201A	Collet adapter 1.500 to 1.750 gage line	$140.00
201B	Collet adapter 1.751 to 2.100 gage line	$160.00
201C	Collet adapter 2.101 to 2.700 gage line	$180.00
201E	Collet adapter 2.701 to 3.200 gage line	$210.00
201D	Collet adapter 3.201 to 3.600 gage line	$260.00
201K	Key	$5.00
202A	Nose ring L-1 (6" O.D. - 4-1/8" I.D.) Aluminum	$120.00
202B	Nose ring L/0 (4-1/2" O.D. - 3-1/4" I.D.) Aluminum	$85.00
202C	Nose ring L/00 (4" O.D. - 2-3/4" I.D.) Aluminum	$75.00
202D	Nose ring threaded 2-1/4" - 8 Steel	$85.00
202E	Nose ring L-2 (8" O.D. - 5-1/4" I.D.) Aluminum	$165.00
203	Tube 1.342 - 1.344 O.D.	$85.00
	Tube over 28" to 38"	$120.00
204A	Hub 2-1/2" (for pricing only, need lathe dimensions, $35 extra for threaded hubs)	$120.00
204B	Hub 3" ...................................................."....................................................	$130.00
204C	Hub 3-1/2" .............................................."...................................................	$140.00
204D	Hub 4" ...................................................."....................................................	$150.00
204F	Hub 4-1/2" ............................................."....................................................	$160.00
205	Actuator Assembly	$325.00
-	2701 Collar	$15.00
-	2702 Screw (for 2701 collar)	$1.00ea (2)
-	2703 Nut (for 2705 cam)	$12.00
-	2704 Bearing and retainer	$85.00
-	2705 Cam	$74.00
-	2706 Collar (knurled)	$39.00
Index Pin Assembly $15.00	2707 Index pin	$5.00
	2708 Knob	$8.50
	2709 Screw (for 2708 knob)	$1.00
	2710 Spring	$2.50
-	2753 Finger	$10.00ea (3)
-	2754 Pivot pin	$2.00ea (3)
220	Tube and finger ring with knurled ring - fingers and pivot pins (easy to exchange)	$245.00
206	Handle casting	$48.00
207	Nut (handle casing)	$1.00ea (2)
208	Screw (handle casing)	$3.00ea (2)
209	Nut	$1.00ea
210	Handle rod	$15.00
211	Handle	$9.95
212	Screw (index ring 213 to hub)	$1.00ea (3)
213	Index ring	$75.00
214	Screw	$1.00ea (2)
215	Bracket	$28.00
216	Bolt and nut	$3.00
217	Connector casting	$28.00
218	Threaded rod	$7.00
219	10-32 - 1/2... 82 degree flat head allen	$1.00ea (3)

CLICK ON IMAGE FOR LARGER VIEW