PRECISION PRODUCTS
7400 SAN FERNANDO RD. SUN VALLEY, CALIFORNIA 91352
ABOUT US CONTACT US ORDERING FREE CATALOG
Copyright J.F.K. Co. Precision Products 2008 - 2009
(WILL CONTINUE TO HOLD PART IF AIR PRESSURE IS LOST)
5-C AIR OPERATED MECHANICAL COLLET CLOSER
THE BEST AIR UNIT ANYWHERE
MODEL AM - for 10" to 18" lathes
1.344 O.D.
Material capacity 1-1/16"
MUST USE A 4-WAY VALVE AND EXHAUST AIR
TO INSTALL AIR OPERATED CLOSER - Mount the unit following the instructions for the HAND LEVER CLOSER where applicable. Mount the air valve within convenient reach of operator. To assure long life for the unit avoid excessive pressure. The unit should operate satisfactorily on 40 psi to 60 psi.
HEAVY DUTY AIR 5-C COLLET CLOSER

MODEL LD 6" Diameter Piston

40 to 60 lbs. air pressure

Air cylinder weight 11 lbs.

Model LD is for use in heavy duty machining, form tool plunging and drilling, wherever stock slippage must be eliminated. The method of manufacture and installation of these cylinders insure the highest degree of maintained concentricity between the cylinder and the machine spindle.
201A
Collet adapter 1.500 to 1.750 gage line
$140.00
201B Collet adapter 1.751 to 2.100 gage line
$160.00
201C Collet adapter 2.101 to 2.700 gage line
$180.00
201E Collet adapter 2.701 to 3.200 gage line
$210.00
201D Collet adapter 3.201 to 3.600 gage line
$260.00
202A Nose ring L-1 Aluminum
$120.00
202B Nose ring L/0 Aluminum
$85.00
202C Nose ring L/00 Aluminum
$75.00
202D Nose ring threaded 21/4"-8 steel
$85.00
202E Nose ring L-2 Aluminum
$165.00
MODEL LD PARTS LIST
LD - 100
Cylinder (Aluminum)
$120.00
LD - 101 Cylinder cap (Aluminum)
$85.00
LD - 102 Piston (Aluminum)
$105.00
LD - 103 Aluminum adjusting tube nut
$20.00
LD - 104 Hub (Steel) (INTERNAL)
$120.00
LD - 105 Sleeve (Steel)
$65.00
LD - 106 Locknut (Steel) with 3-48 allen allen set screw
$20.00
5210KFF Bearing (2)
$48.00ea
SD - 107 Key (Steel)
$5.00
MODEL AM - PARTS LIST
2703
 Threaded Nut (Steel)
$10.50
 8714 Head Rear Cylinder (Aluminum) $95.00
2705
Cam (Steel)
$74.00
8716
Socket Head Cap Screws (6)
$1.00ea
8701
Socket Head Cap Screws (4)
$2.00ea
8717
Head Front (Aluminum)
$155.00
8702
O-ring (Wiper) for rear of head #224
$2.00
8718
Piston Front (Aluminum)
$69.00
8704
Piston Rear (Aluminum)
$75.00
8719
Seal 6226-29 Buna (2)
$10.00ea
8705
Actuator, Brazed Assy. with Fingers, Springs & Knurled Collar
$325.00
8720
Retainer Nut (2)
$32.00
8711
Threaded Retainer Nut (Steel)
$28.00
8721
Bearing For Front Head
$22.00
8712
O-ring For Piston #336
$2.00
8722
Cylinder (Aluminum)
$52.00
8713
Bearing For Piston
$16.00
8723
Ring Stop (Steel)
$10.00
-
-
-
8724
Finger Springs (3)
$3.95
-
-
-
203
Draw Tube
$85.00
O-RINGS
MS28775-136 For LD-100 (2" Diameter) $2.00ea(1)
A-242-BUNA
For LD-101 (4-1/4" Diameter)
$5.00ea(2)
568256
PARCO for LD-102 (6" Diameter)
$6.00ea(1)
SNAP RINGS - ALLEN SCREWS - GASKET
N5002-350 For LD-102 Piston $10.00
1/4-28
Cone Set Screws (1/4" Long)
$2.00ea(3)
3-48
Socket Set Screw (1/8" Long)
$2.00ea(1)
10-24
Cap Screws (3/4" Long)
$2.00ea(8)
10-24
Cap Screws for LD-103 (1/2" Long)
$2.00ea(2)
GASKET
6" Diameter Paper Gasket
$3.00ea(1)
5-C AIR COLLET - Model SCC-C
Bolt Pattern 4.750
The series SCC, double action, air powered 5C Collet Chuck has been developed for drill presses, mill work and taping. Depth positioning of the work piece is repetitive, irreguardless of variation in size. Centering of the work piece is maintained. The opening of the collet releasing the work piece is positive.

Used by most manufacturing plants large or small.

5C Collet wrench is included.

HEIGHT 3-3/8", BASE 5.350 Diameter, Aluminum Body 4" Diameter.

4-3/8" Mounting holes, 2 holes each side of air inlet - 2.370 center to center.

MODEL SCC-C...........................................................................................$345.00
MODEL 800

Yoke 3-1/2" wide

3/4" between air unit

Approx. 16 lbs

For special purpose machine 5-C collets 1 inch capacity.

Space (3/4") for pulley, rack and pinion or other type of drive.

May be used for burring parts, holding parts for milling with rack and pinion gear to rotate unit.

Hold parts in 5C collet for welding.

Pulley for V-belt drive or rack and pinion (not supplied with unit).

2 sets of holes in base, tapped holes 2-3/4" and 4" center to center 3/8"-16 thread. 4 holes .400 diameter 2-3/4" and 6" center to center.

40 to 60 lbs. air pressure recommended

LIGHT DUTY AIR 5-C COLLET CLOSER
SMALL LATHES, CRYSTAL LAKE GRINDER, etc.
3-3/8" DIAMETER PISTON - MODEL SD
Approx. cylinder weight 5 lbs

Air powered, double action, non-rotating collet cylinders for use on lathes, grinders and special purpose machines developed to insure a degree of efficiency and accuracy. Model SD was designed for precision, low speed grinder work heads. Compact and light in weight it will not tilt the work head.

PLUS COLLET ADAPTER, HUB AND NOSE TO FIT YOUR MACHINE (if needed).
201A COLLET ADAPTER
$140.00
201B COLLET ADAPTER
$160.00
201C COLLET ADAPTER
$180.00
202A NOSE RING L-1 Aluminum
$120.00
202B NOSE RING L/0 Aluminum
$85.00
202C NOSE RING L/00 Aluminum
$75.00
202D NOSE RING THREADED 2-1/4"-8 Steel
$85.00
Nose rings for A-1, D-1 Alum. and other than listed - NOT AVAILABLE
MODEL SD - PARTS LIST
SD-101
Hub (Steel - Internal Bearing Hub)
$105.00
SD-102
Back Plate for Piston (Aluminum)
$48.00
SD-103
Piston (Aluminum)
$80.00
SD-104
Sleeve (Steel)
$60.00
SD-105
Cylinder (Aluminum)
$125.00
SD-106
Aluminum Adjustment Nut
$20.00
SD-107
Key (Steel)
$5.00
Collet Draw Tube (Steel)
-
$85.00
FOR O-RINGS  
SD-102 Back Plate - MS28775-235 or Parker 2-235 $4.00ea(1)
SD-102 Back Plate - MS28775-132 or Parker 2-132 $3.00ea(1)
SD-103 Piston - MS28775-235 or Parker 2-235 $4.00ea(1)
SD-105 Cylinder - MS28775-235 or Parker 2-235 $4.00ea(1)
     
FOR SNAP RINGS  
SD-101 Hub #5102-196 $5.00ea(1)
SD-103 Piston #N5002-300 $10.00ea(1)
SD-104 Sleeve #5102-177 $5.00ea(1)
SD-104 Cylinder #N5000-325 $10.00ea(1)
8-32 Cone Set Screws $2.00ea(3)
10-24 Cap Screws for SD-106 (1/2" Long) $2.50ea(2)
Bearing MRC-109KSZZ or N.T.N. 6009LLB $22.00ea(1)
Bearing MRC-210SZZG or N.T.N. 6210LLB $25.00ea(1)
COST OF UNIT COMPLETE FOR D1-6 LATHE.............................$1350.00
(LESS AIR CONTROLS)
BLACK AIR CYLINDER ONLY ........................................................$595.00
NO CAM #2705 - INCLUDES #8711 RETAINER NUT
BASE PRICE...............................................................................................$695.00
Plus collet adapter & hub to fit your lathe, and nose ring (if required)
LATHES BASE PRICE $595.00
CYLINDER ONLY - NO COLLET ADAPTER, NO TUBE OR TUBE NUT
$495.00
NO SPECIAL HUB TO ADAPT AIR UNIT TO LATHE OR GRINDER
MODEL 800............................................................$1295.00
(1)
Collet adapter #7
$140.00
(1)
Threaded nut (Steel)
$42.00
(1)
Bearing 6210LLB
$25.00
(1)
Spacer between bearings
$24.00
(1)
Spindle (Steel)
$260.00
(1)
Snap ring (5108-215)
$5.00
(1)
Yoke (Aluminum)
$195.00
(1)
Aluminum knob
$20.00
(2)
Aluminum cups
$38.00
(1)
Draw tube 6"
$58.00
(2)
Bearing 6011LLU
$22.00
(2)
Snap rings (5102-196)
$5.00
Air cylinder stroke .675 - Air cylinder weight 5 lbs
  • Runs Cool - Air is exhausted from cylinder
  • Mouse trap springs on cam fingers for high speed use
  • Replaceable collet tube
  • The only one of a kind - 15 year improving this unit
  • No brackets - Mount hub to spindle
ABOUT US CONTACT US ORDERING FREE CATALOG
1-818-767-6707
Fax 1-818-767-1637
HOME